AUTOMATIC MAINS FAILURE ? ENHANCED AUTO/AMF SURF V1.3a
AUTOMATIC MAINS FAILURE- LITE VERSION AUTO/ AMF SURF LT V1.0
Automatic mains failure or Auto Start controller
Simultaneous display of AC voltage, currents, frequency, hour counter, oil pressure, engine temperature and battery voltage
Display of power in KW and energy in KWh of both engine and Utility
Display of fuel consumption rate (L/h), total fuel consumption, tank percentage and RPM
Display of power factor of each line
Display of Software version, the date and time, the continuous hour counter and the utility hour counter
CAN bus J1939
CAN bus with BAMVI_CAN that can read DC voltage up to 275Vdc and DC current up to +-300Amps (Optional)
USB interface
Interfaces RS485 Modbus/CAN
On-site firmware upgrade
AUTOMATIC TRANSFER SWITCH CONTROLLER OMEGA ATS V1.2 / STD - E - M - EM
For 1 utility (optional) & 2 generators of the same rating: Alternate function to keep running hours of the gensets equal
For 1 utility (optional) & up to 3 generators of different rating: Automatic switching between the gensets based on the load
Isolated measurement of the voltages and frequency on all sources
Current measurement on the load side
Graphical LCD display
4GB Micro SD card for event and data logging
Ethernet interface
USB interface
Serial RS485 Modbus protocol
Internet communication
On-site firmware upgrade
AUTO START WITH VOLTAGE AND FREQUENCY SMART/TURBO
Voltage display & protection
Battery voltage display & protection
Frequency display & protection
Run hour counter
Run hours since the last oil change
AUTO START WITH VOLTAGE, FREQ AND CURRENT SMART/GT
Voltage display & protection
Battery voltage display & protection
Frequency display & protection
Current display & protection
Oil Pressure display & protection
Temperature display & protection
Run hour counter
Run hours since the last oil change
On-site firmware upgrade
12V/5A Battery charger (Input: 90-240VAC) MAXIBAT
Intelligent 12v/5A battery charger
LCD display
Display of the battery voltage, current and charge status
Charging operating modes: trickle, boost, float, and full
12V/3A Battery charger (Input: 48VDC) CHARGER-48i
12V/3A battery charger from 48V battery source
Charging operating modes: boost and float
DIESEL KEY START WITH LOW COOLANT SMD DKSTLS
DIESEL KEY START BOARD SMD DKSTS
DIESEL REMOTE START BOARD DRST
Presettable response delay
Presettable cooling delay
Presettable starter time
Three to four starting attempts
Universal supply voltage
Alarm output
SMART KWHMETER WITH RS485 (MODBUS) RM-MB-20A
LCD display for energy in KWh and AC voltage
LCD display for frequency and current
LCD display for subscription status
Over current monitoring
Power cut relay
DIGITAL THREE PHASE VOLTAGE RELAY PH3D V13 / STD_1C - STD_2C
Display of all voltages
Over/Under voltage
Phase failure
Wrong phase sequence
Asymmetry
DIGITAL SINGLE PHASE VOLTAGE RELAY SPHD V1.3
Voltage display
Over/Under voltage
PHASE SEQUENCE / FAILURE RELAY PHF V2.1
Phase failure detection
Wrong phase sequence detection
DIGITAL FREQUENCY RELAY FRWD V1.3
Frequency display
Over/Under frequency
DIGITAL CURRENT RELAY OCR1D V1.0
Current display
Over/Under current
Submersible water pump application
DIGITAL BATTERY VOTLAGE MONITOR BAMVI.STD
DC voltage (Up to 330 V) monitoring
Auxiliary supply control
DIGITAL BATTERY VOLTAGE AND CURRENT MONITOR BAMVI.C
DC voltage (Up to 330 V) & DC current (Up to +/- 300A) monitoring
Auxiliary supply control
DIGITAL BATTERY VOLTAGE & CURRENT MONITOR W CAN BUS BAMVI/CAN
CAN Bus communication
DC voltage (Up to 330 V) & DC current (Up to +/- 300A) monitoring
Auxiliary supply control
PLC CURRENT INTERFACE PLC CI
0-5A Current transducer with 0-10VDC output
True root mean square (rms) current measurement
Interfaces with 5A current transformer
Case conforms to DIN 43 880 of the British Standard